Technology
Standards and certificates: CE, EN 934-2, EN 1504 and the EPD
Penetron's Dutch-language data sheets state the standard and the CE marking for each product. Here they are brought together, with the documents and the environmental product declaration, for anyone preparing a specification or a tender.

Anyone who specifies Penetron must be able to refer to a standard and to a document. This page lists the standards named on the data sheets, the documents available on the product pages and what you can request from Penetron Benelux in Herentals.
Which standards appear on the data sheets
On the Dutch-language data sheets, these products carry a CE marking, with the standard the product falls under.
| Product | Standard on the data sheet | What it is |
|---|---|---|
| Penetron Admix | EN 934-2 | Crystalline admixture in powder form, for the concrete mix |
| Penetron Admix SB | EN 934-2 | The same powder in dissolvable 3 kg bags |
| Penetron Slurry | EN 1504-2, EN 1504-3 and EN 1504-7 | Crystalline slurry for existing concrete |
| Penecrete Mortar | EN 1504-3 | Crystalline repair mortar |
| Peneplug | EN 1504-3 | Fast-setting mortar for active leaks |
| Penetron Inject | EN 1504-5 | Crystalline injection grout |
| Penetron Quick Patch | EN 1504-3 | Fast-hardening repair mortar for horizontal surfaces |
| Penetron V/O Patch | EN 1504-3 | Mortar for vertical and overhead repairs |
| Penetron Grout | EN 1504-3 | Non-shrink grout |
| Penetron Seal Coat | EN 1504-2 | Cement-based waterproof coating |
| Peneseal FH, FH-PS and Pro | EN 1504-2 | Penetrating sealers for concrete surfaces |
If a product is not in the table, ask Penetron Benelux which marking and which documents are available.
EN 934-2 for Admix, EN 1504 for slurry and mortars
Penetron Admix and Admix SB fall under EN 934-2, the European standard for admixtures for concrete. The Admix data sheet also describes the product as an admixture to reduce permeability under hydrostatic conditions (PRAH). Admix also exceeds the requirements of the American standard ASTM C494, type S.
For Penetron Slurry, three parts of EN 1504 appear on the data sheet. Under EN 1504-3, the slurry is a mortar for structural and non-structural repairs. The CE block also gives the water vapour permeability, the capillary absorption, the resistance to chemical attack and the corrosion protection. Penetron Inject falls under EN 1504-5 as an injection grout.
The documents for each product
The product pages carry the technical data sheet, with the properties, the instructions for use and the consumption, and the safety data sheet. For some products there is also a brochure, such as for Peneseal FH, Peneseal Pro and Penetron Biomic.
The declaration of performance (DoP) goes with the CE marking. If you need it for a file or a tender, request it from Penetron Benelux. You can also ask for help with specification text: an adviser reads it through and adds to it where needed.
If the application involves drinking water, first check which approvals are available for Belgium or the Netherlands before you specify the product.
The environmental product declaration (EPD)
EPD stands for environmental product declaration, in Dutch a milieuproductverklaring. One exists for Penetron Slurry and Penetron Admix together in The International EPD System, with registration number S-P-2038. It was prepared in accordance with ISO 14025 and EN 15804, published on 4 May 2020, revised on 2 May 2024 and is valid until 1 May 2029.
For the swellable waterstop Penebar SW-55 there is a separate EPD, S-P-04710, dated 4 February 2022. It was prepared for the United States and is valid until 31 January 2027. You can read more about Penetron's approach to CO2 at Towards Zero Carbon.
Crack width in the specification
The data sheets for Penetron Slurry, Penetron Admix and Admix SB give 0.5 mm as the width of the hairline cracks that the crystals seal. That is what the product does. The crack width a structure may have follows from the design.
Two sites in Ghent show how the two fit together. At the sludge bunker for Aquafin, with BM Engineering as engineering consultant, the issue was watertightness at crack widths between 0.1 and 0.3 mm. For the new foundation slab for PVS Chemicals, the concrete had to meet the requirements of Eurocode 2. In consultation with the customer and the concrete supplier, Admix SB was chosen there, with an adapted concrete quality.
Questions
Does Penetron Admix have a CE marking?
Yes. The Dutch-language data sheet for Penetron Admix states the CE marking in accordance with EN 934-2. The same applies to Penetron Admix SB.
Where can I find the declaration of performance?
Request it from Penetron Benelux, together with the other documents you need for your file. The technical data sheet and the safety data sheet are on the product page.
Is there an EPD for Penetron?
Yes, for Penetron Slurry and Penetron Admix together: S-P-2038 in The International EPD System, valid until 1 May 2029. There is a separate EPD for Penebar SW-55.
What crack width does Penetron Admix seal?
Hairline cracks up to 0.5 mm. The crack width your structure may have is set out in the design. At the Aquafin sludge bunker in Ghent, the crack widths were between 0.1 and 0.3 mm.
Also read
More about concrete and waterproofing
Crystalline waterproofingHow crystalline waterproofing works: crystals seal pores and hairline cracks up to 0.5 …
Towards Zero CarbonTowards Zero Carbon: how Penetron's crystalline concrete protection extends the service …
Waterproof concrete from the ready-mix concrete plantWaterproof concrete from the ready-mix concrete plant with Admix, Admix SB or Admix …
Contact
Discover how Penetron can strengthen your next construction project
Tell us about your project. We will help you choose the right product.